Parts & Accessories

Our thru-axle kit comes with everything you need to mount most 12x142 thru-axle bikes on your KICKR SNAP indoor trainer. This accessory will work with all editions of the Wahoo KICKR SNAP. It includes the following: - Threaded axle spacer M12 x 1.75 Coarse - M12 x 1.5 Medium - M12 x 1.0 Fine - End Cap

We designed Teravail tubeless tape for no-hassle installation. Its slight stretch allows the tape to easily conform to your rims. The translucent material shows you exactly where the tape makes contact. It's tacky enough to prevent shifting but easy to pull up if needed, and it won't leave residue on your rims. - Teravail Tubeless Tape comes in a variety of widths to fit almost any rim. - Teravail Tubeless Tape is available in a variety of widths and roll lengths. - Ten-meter length is enough for a single layer on approximately four wheels

Replacement clear plastic spoke guard.

Durasync freehub bodies feature triple freehub bearings for increased axle stability to handle even greater vertical and torsional loads. This CNC machined durasync freehub is a direct replacement for your Neo hub, and includes pawls, springs, pawl retaining ring, and red freehub spacer. Bearings are pre-installed. - 6-pawl system provides 36 points of contact and 10-degree engagement for quick acceleration - Chromed steel bearings - Wide bearing stance and axle design reduces flex and adds durability - Low drag main seal prevents contamination and reduces resistance - Mini Driver has a Shimano HG spline, but is 10mm shorter to accept 11-speed cassettes with 10t cogs from Hope and OneUp Components

- Replacement rear wheel skewer. - Specifically designed for use with Saris trainers. - Can be used for both indoor and outdoor rides.

Lightweight and easy to install, there are Ritchey rim strips for all wheel sizes and types. - Easily snaps over your rims - Stretchy, tightly woven material provides a close fit and protects from abrasion - Sold as a pair - Not for tubeless set up

Refresh your Bontrager wheels. Genuine replacement parts When it's time to refresh your trusty wheelset, Trek Genuine Replacement Parts have you covered. - Original equipment replacement freehub body, to be used with 7-speed cassettes - Compatible with Bontrager 7-speed wheels with a freehub body - Not compatible with wheels using a threaded freewheel

Refresh your Bontrager wheels. Genuine replacement parts When it's time to refresh your trusty wheelset, Trek Genuine Replacement Parts have you covered. - Replacement freehub bodies for Bontrager DCL-141Q hub - Compatible with Bontrager DCL-141Q - End cap not included

Upgrade or refresh your Bontrager wheels. Genuine replacement parts Whether you're looking to upgrade to the newest and freshest drivetrain or simply hoping to refresh your trusty wheelset, Trek Genuine Replacement Parts have you covered. - Replacement freehub body - Compatible with Bontrager Rapid Drive 108 hubs - Pawls and springs sold separately - Install 3 pawls/springs for 54 tooth engagement or 6 pawls springs for 108 tooth

Upgrade or refresh your Bontrager wheels. Genuine replacement parts Whether you're looking to upgrade to the newest and freshest drivetrain or simply hoping to refresh your trusty wheelset, Trek Genuine Replacement Parts have you covered. - Replacement freehub body - Compatible with Bontrager Rapid Drive 108 hubs - Pawls and springs sold separately - Requires Micro Spline specific end cap

Tubeless setup made easy with valve stems designed to work as a system with Bontrager wheels, tires and rim strips The valves you need to upgrade to Tubeless These rim valves are crucial in upgrading your Tubeless Ready (TLR) Bontrager wheels to the next level of dependability and performance. Product details - To be used exclusively with Bontrager Tubeless Ready (TLR) wheels - Use only with Bontrager TLR rim strip with rectangular base - Required for Bontrager's Tubeless Ready (TLR) system setup - Removable valve core for easy sealant fill - Sold as singles

These rim valves are crucial in upgrading your Tubeless Ready (TLR) Bontrager wheels to the next level of dependability and performance. Key features: - To be used exclusively with Bontrager Tubeless Ready (TLR) wheels - Required for Bontrager's Tubeless Ready (TLR) system setup - Removable valve core for easy sealant fill - Silver MTB valve is compatible with all Bontrager Mountain wheels except: Line XXX, Kovee XXX, and Line Pro 40 - Alloy Road Tubeless Rim Valve is compatible with all Bontrager alloy TLR road wheels

These original replacements will get your wheels working like new. - Alloy thru-axle that can be used with a 6mm hex wrench or with a lever - Keep it light by removing the lever and instead use a 6mm hex wrench - Keep it convenient by keeping the lever inside the axle - Lever is held securely by internal O-ring - Lever sold separately

These rim strips are crucial in upgrading your Tubeless Ready (TLR) Bontrager wheels to the next level of dependability and performance. Key features: - To be used exclusively with Bontrager 29"/700c Tubeless Ready (TLR) wheels - TLR Rim Strips are the light and easy solution to Bontrager Tubeless conversion - Rim Strip replacement is recommended if removed from the wheel - For specific compatibility, access 'WHEELS' tab on the Tech Site or contact Customer Service

Bontrager Tubeless (TLR) Rim Tape creates an air-tight seal that covers spoke holes in the rim for easy tubeless tire setup and installation. The tape securely bonds to the rim and doesn't leave residue when removed. For use with wheels approved for TLR Tape-based tubeless conversion. - Provides durable, air-tight seal over spoke holes for tubeless conversion - Wrap four wheels with a single layer of tape or two wheels with a double layer - Provides secure adhesion to rim without leaving residue when removed - Thoroughly clean and dry rim bed before applying - For use with rims approved for TLR Tape-based tubeless conversion

This rim tape is crucial in upgrading your Tubeless Ready (TLR) Bontrager wheels to the next level of dependability and performance. - TLR Rim Strips are the light and easy solution to Bontrager Tubeless conversion - Tape is designed for wider Plus and Fat wheels - Can also be used as a universal tubeless solution for non-Bontrager rims - Use only with Bontrager TLR rim valve with round base - Rim tape replacement is recommended if removed from the wheel - One roll is 5m (197") in length

Zipp 101 XPLR MOTO Rim Strip And Tubeless Tape Kit (includes rim strip and tubeless tape for 1 wheel).

This 11-speed freehub is only compatible with model-year 2013 (V8) and 2014 (V9) Zipp wheelsets. Check that your hub has a black end cap before using this freehub. Use the spacer for compatibility with 10-speed Shimano and SRAM drivetrains after installation. The red freehub is designed for SRAM or Shimano drivetrains and includes a spacer for 10-speed compatibility. The blue freehub is designed for Campagnolo drivetrains. The Campagnolo version requires one 0.25mm axle washer, which is included. - 10 to 11-speed wheel conversion can only be completed by an authorized Zipp Service Center - Not intended to convert older 10-speed freehub wheels to 11-speed freehub wheels - Only intended to swap freehub compatibility (SRAM/Shimano - Campagnolo) with current 11-speed wheels - Includes cassette spacer - Material: Aluminum

Includes rim strip and tubeless tape for 1 wheel.

- Wheel bearing kit front/rear - Bearing dimensions: 17 x 30 x 7mm - Material: steel - 2 pieces

Wheel Conversion Caps for Zipp 77/177 Disc hubs. Converts your Zipp 77 or 177 hubs to nearly any frame standard.

Package comes with two pieces of rim tape for use with the Zipp clinchers. Woven nylon material. Tape is extra thin with a thickness of 0.5 mm. Note: For Zipp 700c and 650c aluminum/carbon hybrid clichers, use the 16 mm rim tape. For Zipp 30 wheel set use 18mm but for the wider Firecrest and Firestrike carbon clinchers use the 20mm x 1/2mm rim tape.

- Lowest resistance hybrid ceramic (ceramic balls and steel cages) available - Measurable wattage savings between 1.5 and 9 watts per bearing set, depending on the level and condition of your existing bearings - Kits include Freehub body with CeramicSpeed

Freehub bodies for Zipp Cognition hubs.

- Freehub for Cognition V2 hubs

Zipp Speed Weaponry Rear Axle Conversion Kit - Not to be used on 188 V6 or earlier rear hubs - Only to be used to convert Zipp's 188 V7 10-speed rear hubs to 11-speed

These die-cut borderless decals provide a distinctive look to go with the distinctive sound and aero-advantage of Zipp wheels rolling at 45km an hour. Zipp’s Matte white and Matte black decals also are still available. Each decal kit has seven decals sufficient to cover one wheel and two matching valve-hole decals. Note: Before applying the decals, make sure the rim surface is free of dirt and debris. We recommend a gentle wipe with acetone or rubbing alcohol. Peel the white backing sheet from the decal, orientate, position and gently press the decal onto the rim surface. Starting at one end, remove the surface clear cover slip and then work the decal into the dimples using a 3M squeegee.

Wheel Freehub Kit—(Includes Bearings & Pawls) 11/12 Speed XD—X0 HUBS/RISE 60 (B1)/ROAM 30/ROAM 40/RAIL 40/RISE XX/ROAM 50/60 (B1) Compatible With: HU-X0-A1, WH-RAIL-40-A1, WH-RISE-60-B1, WH-RISE-XX-A1, WH-ROAM-30-A1, WH-ROAM-40-A1, WH-ROAM-50-A1, WH-ROAM-50-B1, WH-ROAM-60-B1

Wheel Freehub Kit—XD Driver Body Kit—Zipp ZM2 - Compatible With: WH-MOTO-30-B1

Wheel Freehub Kit SS 176/177 SRAM XDR - End Caps Not Included Compatible With: WH-202-CCR-A1, WH-202-TLD-A1, WH-202-TUD-A1, WH-302-CCD-A1, WH-302-CCR-A1, WH-302-TLR-A1, WH-303-CCR-B1, WH-303-TLD-A1, WH-303-TUD-B1, WH-303-TUR-B1, WH-30C-CLD-A1, WH-30C-CLR-A1, WH-404-CCR-A1, WH-404-CCR-B1, WH-404-TLD-A1, WH-808-CCR-B1, WH-808-TLD-A1, WH-SP9-CC30-A1, WH-SP9-CCD-A1, WH-SP9-CCR-A1, WH-SP9-TUD-A1